PowderRiver Trade stocks structural screws, concrete anchors, drill bits, and pre-built contractor packs for residential framing, commercial build-out, and industrial maintenance across Albany and Laramie counties.
From #8 drywall screws to ¾-inch wedge anchors, every line in our catalog includes published torque specs, substrate compatibility data, and manufacturer grade certifications — so your crew picks the right fastener the first time.
Need a takeoff list matched to your plans? Bring your cut sheet or email your BOM — we cross-reference every line item against in-stock inventory and suggest equivalents where needed.
Application Guide →
PRT-FST-001
Hex bolts, carriage bolts, nuts, washers, and machine screws in Grade 2, 5, and 8 steel. Hot-dip galvanized and stainless options for exterior and corrosive environments.
PRT-SCR-002
Code-approved structural screws for wood-to-wood, wood-to-steel, and composite connections. Simpson Strong-Tie, GRK, and Spax lines with published ICC-ES evaluation reports.
PRT-ANC-003
Wedge anchors, sleeve anchors, drop-in anchors, and adhesive anchor systems for concrete, block, and brick. All anchors include embedment depth charts and torque specifications.
PRT-DRL-004
SDS-plus and SDS-max masonry bits, spade bits, hole saws, step bits, and metal drill bits from Irwin, Bosch, and Milwaukee. Sold individually and in contractor multi-packs.
PRT-PCK-005
Pre-sorted, job-ready fastener assortments organized by trade and project type. Eliminate mid-job supply runs with packs sized for framing, drywall, decking, and concrete formwork.
PRT-IND-006
Stainless A193 B7 studs, U-bolts, J-bolts, turnbuckles, and cable railing hardware for commercial and industrial applications. Metric and imperial threads in stock.
Selecting the wrong anchor is one of the most common — and most expensive — mistakes on a job site. PowderRiver carries the full range of mechanical and adhesive anchors with published load tables, embedment depth requirements, and installation tooling for every diameter we stock.
Through-fixture anchoring in solid concrete. Full diameter embedment required. Available zinc-plated and 304 stainless for exterior and corrosive environments.
Hollow block, brick, and solid concrete. Expanding sleeve distributes load across base material. Ideal for medium-duty fixtures and conduit straps.
Light- to medium-duty anchoring without a separate anchor body. Blue Climaseal coating for corrosion resistance. Pre-drill with matched carbide bit.
Epoxy and vinylester systems for post-installed rebar, heavy equipment, and high-load structural connections. ICC-ES evaluated Hilti HIT-HY and Simpson SET-XP systems.
Use this reference to identify the correct fastener category for common construction substrates. Always verify with the manufacturer's published load data for your specific application and local code requirements.
IRC-compliant structural connections in wood framing require fasteners with published ICC-ES evaluation reports. Generic deck screws do not qualify for structural shear connections — use code-listed products only.
| Application | Recommended Product | Spec Notes |
|---|---|---|
| Stud-to-plate framing | 16d sinker nails or SDS screws | 3½" min penetration into receiving member |
| Shear wall sheathing | 8d common nails @ 6" o.c. | Match nailing schedule on engineered plans |
| Beam-to-post connection | Simpson A35 or LSSU angle + SDS | Follow connector manufacturer load tables |
| Truss-to-wall connection | Hurricane clips (H2.5A or equal) | Required in high-wind zones per IRC |
| Ledger board attachment | ½" lag screws or through-bolts | Do not use nails; follow IRC R507.2 |
Anchor selection depends on base material (solid concrete vs. hollow block), load type (static, seismic, vibratory), and environment (interior, exterior, chemical exposure). Minimum embedment depth is non-negotiable — never cut anchors short.
| Application | Recommended Product | Spec Notes |
|---|---|---|
| Equipment anchoring (solid) | ½" wedge anchor, 4" embedment | Torque to manufacturer spec; inspect threads |
| Hollow block walls | ¼" – ⅜" sleeve anchor | Do not use wedge anchors in hollow CMU |
| Light conduit & strut | ¼" Tapcon, 1" min embedment | Pre-drill with matched carbide masonry bit |
| Post-installed rebar | Epoxy adhesive (HIT-HY 200) | Hole diameter = bar dia + ⅛"; ICC-ES required |
| Form tie replacement | Drop-in anchor + threaded rod | Requires setting tool; flush mount |
Metal-to-metal and metal-to-wood connections require self-drilling or pre-drilled fasteners with published shear values. Stainless is mandatory within 500 feet of salt exposure or in treated lumber contact applications.
| Application | Recommended Product | Spec Notes |
|---|---|---|
| Steel stud framing | #8 self-drilling pan head | Drill point must penetrate both plies |
| Metal roofing panels | #12 metal-to-metal screw w/ EPDM | Do not over-torque; EPDM washer seals |
| Strut channel mounting | ⅜" hex head bolt + strut nut | Spring nut for vertical strut applications |
| Deck ledger to steel | Stainless through-bolt w/ plate washer | 316 SS required for ACQ-treated lumber contact |
| Sheet metal ductwork | #8 hex washer self-drilling | Minimum 3 threads beyond connection |
Interior finish fasteners are specified by gauge, thread type, and coating. Coarse-thread screws are for wood studs; fine-thread for 20–25 gauge steel studs. Screws must seat below paper surface without tearing face paper.
| Application | Recommended Product | Spec Notes |
|---|---|---|
| 1/2" drywall to wood studs | #6 × 1¼" coarse thread, black phosphate | 16" o.c. field; 8" o.c. edges per ASTM C754 |
| 1/2" drywall to steel studs | #6 × 1" fine thread, black phosphate | Self-drilling point; 20–25 ga studs |
| Ceiling board (5/8" Type X) | #6 × 1⅝" coarse thread | 12" o.c. field; use screw gun clutch |
| Corner bead attachment | 1¼" drywall nails or staples | 6" o.c.; set flush without buckling bead |
| Cabinet hanging | #10 × 3" cabinet screw | Must hit stud; use wall anchors only for light loads |
Exterior fasteners must resist corrosion from moisture, UV, and chemical treatment in lumber. ACQ- and CA-treated lumber requires hot-dip galvanized (ASTM A153 Class D) or stainless fasteners — standard zinc will corrode rapidly.
| Application | Recommended Product | Spec Notes |
|---|---|---|
| Deck board to joist | #10 × 3" composite deck screw | 316 SS for coastal; ceramic coat for inland |
| Joist hanger nails | 1½" × 0.148" hanger nails (HDG) | Do not substitute common nails in hangers |
| Railing post to deck frame | ½" through-bolt w/ blocking | Through-bolt required; lag screws insufficient per IRC |
| Fence pickets to rail | #8 × 2" exterior screw (SS or ceramic) | Pre-drill hardwood to prevent splitting |
| Siding attachment (fiber cement) | Corrosion-resistant siding nail | Blind-nail or face-nail per manufacturer spec |
Pre-counted, labeled, and organized by trade. Grab a pack at the counter or add packs to your standing order — every pack includes a contents manifest for your job cost records.
Essential fasteners for a two-person framing crew on a single-family residential project. Covers one week of typical stick-frame work.
Complete fastener set for commercial tenant improvement — metal stud framing, drywall, and ceiling grid. Sized for a 5,000 sq ft build-out.
Mechanical and adhesive anchor assortment for equipment setting, conduit, and structural connections in concrete and block.
Side-by-side comparison of common fastening methods by substrate, load capacity, and installation requirements. Use as a field reference — confirm final selection with engineer-of-record on structural connections.
| Fastener Type | Best Substrate | Load Range | Install Method | Reusable |
|---|---|---|---|---|
| Wedge Anchor | Solid concrete | Medium – Heavy | Drill, clean hole, torque nut | No — permanent |
| Sleeve Anchor | Concrete, block, brick | Light – Medium | Drill, insert, tighten nut | Removable with effort |
| Drop-In Anchor | Solid concrete (flush) | Medium | Drill, set with tool, thread bolt | Yes — bolt removable |
| Tapcon Screw | Concrete, block | Light – Medium | Drill with carbide bit, drive screw | Removable |
| Adhesive Anchor | Concrete (cracked/uncracked) | Heavy – Very Heavy | Drill, clean, inject, insert rod | No — permanent |
| SDS Structural Screw | Wood, engineered lumber | Medium – Heavy | Pre-drill or self-drill, drive | Removable (damages wood) |
| Lag Screw | Wood to wood/steel | Medium – Heavy | Pre-drill pilot + shank holes | Removable |
| Self-Drill Screw | Steel stud, metal panel | Light – Medium | Drive with impact or screw gun | Removable |
| Drywall Screw | Wood or steel stud | Light (non-structural) | Screw gun, clutch set | Removable |
| Toggle Bolt | Hollow wall (drywall) | Light – Medium | Drill hole, insert, tighten | Removable |
Stick-frame, truss, and SIP connections
Metal stud, drywall, and ceiling grid
Corrosion-resistant exterior fasteners
Anchor systems and specialty hardware
Not a catalog house — real inventory in our Laramie warehouse. Walk in with a part number or broken sample and walk out with the match.
Every structural screw and anchor includes manufacturer load tables, ICC-ES reports, and torque specifications at the counter and on request.
Net-30 terms, volume pricing tiers, and standing order programs for crews that burn through fasteners every week.
Send your BOM or takeoff list — we assemble custom contractor packs labeled by phase, trade, or floor level for your job site.
Email a BOM, bring a takeoff sheet, or describe the connection — we identify the correct product line.
We cross-check every line against substrate, load requirement, and code listing before quoting.
Counter pickup same day, or delivery to Laramie-area job sites on orders placed before 11 AM.
Receive spec sheets, ICC-ES reports, and lot numbers with every structural fastener order.
"We frame eight to ten houses a year and PowderRiver's framing pack saves us two supply runs per project. Everything is counted, labeled, and the SDS screws are the right ones — not whatever was cheapest."
"I needed 3/8 wedge anchors for a equipment pad and three other suppliers were backordered. PowderRiver had four brands in stock with load tables printed and ready. That's why I drive across town."
"Their custom pack service is underrated. We send the takeoff, they build packs by floor level, and deliver to the job site labeled Monday morning. Our waste is down and our crews aren't idle waiting for screws."
PowderRiver Trade Inc started on East Palmer Drive with a simple premise: Wyoming contractors shouldn't wait three days for a box of wedge anchors shipped from Denver. We built a 12,000-square-foot warehouse stocked with the fasteners, screws, anchors, and drill bits that local crews actually use — not a truncated catalog of consumer-grade hardware.
Today we serve 280+ contractor accounts across Albany, Laramie, and Carbon counties. Our counter staff includes former framers and commercial carpenters who understand the difference between a Tapcon and a wedge anchor — and why putting the wrong one in a seismic connection is a problem nobody wants.
Every structural product we sell carries a published specification. We don't stock ungraded imports, off-brand adhesives, or fasteners without traceable lot numbers. If it doesn't have a spec sheet, it doesn't go on our shelf.
Browse our product lines, explore the substrate application guide, or review contractor pack options — everything you need to spec the right fastener before your crew arrives on site.